Share
Pin
Tweet
Send
Share
Send
For work you will need the following materials and tools:
- Copper or aluminum wire, length - 40 cm., Thickness - 1.5 mm. In order to get copper or aluminum wire, you can take the wires and remove insulation from them.
- Thin wire for beadwork, thickness - 0.3 mm (sold in needlework stores).
- Green beads.
- Bright beads (will be used to simulate Christmas balls).
- Round pliers.
- Nippers.
- Hammer and anvil (instead of an anvil, you can use, for example, a metal dumbbell).
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka.jpg)
To get started, take a thick wire with pliers at the very tip and bend to get a loop.
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka-2.jpg)
Next, we begin to bend the wire in such a way that it looks like a curvy "snake". In this case, each subsequent round should be several millimeters longer than the previous one.
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka-3.jpg)
Now we continue to bend the wire in the same vein. It will be more convenient to bend the wire with round-nose pliers, clamping it in the supposed places of the bend. We try to make the distance between the turns approximately the same.
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka-4.jpg)
Such a design should be obtained. At the end of the wire we again make a loop.
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka-5.jpg)
This will be the basis for the future "Christmas tree". Next, we lay the foundation on the anvil and beat off the wire with a hammer in the places of bending, in the resulting structure.
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka-6.jpg)
This process is needed so that the base of the "Christmas tree" could lie in the same plane and to give elegance to the coils.
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka-7.jpg)
After all this, we begin to decorate the basis of the decoration. For this purpose, you need to take a thin wire for beadwork. You can attach, for example, a star or just a beautiful bead to the upper eyelet. We pass a thin wire into the hole and wind the star or bead to the upper loop.
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka-8.jpg)
Then we go down below and start wrapping a thick thin wire every 3-4 turns, stringing one green bead and wrapping it on a thick wire base.
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka-9.jpg)
We reach the end of the turn and string a larger, brighter bead (to simulate Christmas balls) on a thin wire and in the same way we wind it to the base from one turn to another.
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka-10.jpg)
Further following this technology, we continue to decorate the base to the very end of the wire.
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka-11.jpg)
Here is approximately what can result from the work done.
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka-12.jpg)
Such a "Christmas tree" will become an elegant and original decoration for your New Year tree.
![](http://img.uaft2404.org/img/sdela-2019/novogodnee-ukrashenie-yolochka-13.jpg)
Share
Pin
Tweet
Send
Share
Send